Short Description
QSFP+ 40Gb/s LR4 Optical Transceiver
Applications:
This product is a transceiver module designed for 40km optical communication applications. The design is compliant to 40GBASE-LR4 of the IEEE P802.3ba standard. The module converts 4 inputs channels (ch) of 10Gb/s electrical data to 4 CWDM optical signals, and multiplexes them into a single channel for 40Gb/s optical transmission. Reversely, on the receiver side, the module optically de-multiplexes a 40Gb/s input into 4 CWDM channels signals, and converts them to 4 channel output electrical data.
The central wavelengths of the 4 CWDM channels are 1271, 1291, 1311 and 1331 nm as members of the CWDM wavelength grid defined in ITU-T G.694.2. It contains a duplex LC connector for the optical interface and a 38-pin connector for the electrical interface. To minimize the optical dispersion in the long-haul system, single-mode fiber (SMF) has to be applied in this module.
The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP+ Multi-Source Agreement (MSA). It has been designed to meet the harshest external operating conditions including temperature, humidity and EMI interference
Absolute Maximum Ratings
It has to be noted that the operation in excess of any individual absolute maximum ratings might cause permanent damage to this module.
Parameter | Symbol | Min | Max | Unit | Notes |
Storage Temperature | TS | -40 | 85 | oC |
|
Operating Case Temperature | TOP | 0 | 70 | oC |
|
Power Supply Voltage | VCC | -0.5 | 3.6 | V |
|
Relative Humidity (non-condensation) | RH | 0 | 85 | % |
|
Damage Threshold, each Lane | THd | -3 |
| dBm |
|
Recommended Operating Conditions and Power Supply Requirements
Parameter | Symbol | Min | Typical | Max | Unit | Notes |
Operating Case Temperature | TOP | 0 |
| 70 | oC |
|
Power Supply Voltage | VCC | 3.135 | 3.3 | 3.465 | V |
|
Data Rate, each Lane |
|
| 10.3125 |
| Gb/s |
|
Control Input Voltage High |
| 2 |
| Vcc | V |
|
Control Input Voltage Low |
| 0 |
| 0.8 | V |
|
Link Distance with G.652 | D | 0.002 |
| 40 | km |
|
Electrical Characteristics
The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
Parameter | Test Point | Min | Typical | Max | Unit | Notes |
Power Consumption |
|
|
| 3.5 | W |
|
Supply Current | Icc |
|
| 1.06 | A |
|
Transceiver Power-on initialization Time |
|
|
| 2000 | ms | 1 |
Transmitter | ||||||
Single-ended Input Voltage Tolerance (Note 2) |
| -0.3 |
| 4.0 | V | Referred to TP1 signal common |
AC Common Mode Input Voltage Tolerance |
| 15 |
|
| mV | RMS |
Differential Input Voltage Swing Threshold |
| 50 |
|
| mVpp | LOSA Threshold |
Differential Input Voltage Swing | Vin, pp | 190 |
| 700 | mVpp |
|
Differential Input Return Loss |
| See IEEEE 802.3 ba 86A.4.11 | dB | 10MHz-11.1GHz | ||
J2 Jitter Tolerance | Jt2 | 0.17 |
|
| UI |
|
J9 Jitter Tolerance | Jt9 | 0.29 |
|
| UI |
|
Data Dependent Pulse Width Shrinkage (DDPWS ) Tolerance |
| 0.07 |
|
| UI |
|
Eye Mask Coordinates {X1, X2, Y1, Y2} |
| 0.11, 0.31, 95, 350 | UI mV | Hit Ratio = 5x10-5 | ||
Receiver (each lane) | ||||||
Single-ended Output Voltage |
| -0.3 |
| 4.0 | V | Referred to signal |
AC Common Mode Output Voltage |
|
|
| 7.5 | mv | RMS |
Differential Output Voltage Swing | Vout,pp | 300 |
| 850 | mvpp |
|
Differential Output Impedance | Zout | 90 | 100 | 110 | ohm |
|
Termination Mismatch at 1MHz |
|
|
| 5 | % |
|
Differential Output Return Loss |
|
| dB | 10MHz*11.1GHz | ||
Common Mode Output Return Loss |
|
| dB | 10MHz*11.1GHz | ||
Output Transition Time |
| 28 |
|
| Ps | 20% to 80% |
J2 Jitter Output | Jo2 |
|
| 0.42 | UI |
|
J9 Jitter Output | Jo9 |
|
| 0.65 | UI |
|
Eye Mask Coordinates {X1, X2, Y1, Y2} |
| 0.29, 0.5, 150, 425 | UI mV | Hit Ratio = 5x10-5 |
Notes: