Short Description
QSFP+-40Gb/s ER4 QSFP+ 40G, 1340nm, 10km, ER4 Single Mode
Application
This product is a transceiver module designed for 10-20km optical communication applications. The design is compliant to 40GBASE-LR4 of the IEEE P802.3ba standard. The module converts 4 inputs channels (ch) of 10Gb/s electrical data to 4 CWDM optical signals, and multiplexes them into a single channel for 40Gb/s optical transmission. Reversely, on the receiver side, the module optically de-multiplexes a 40Gb/s input into 4CWDM channels signals, and converts them to 4 channel output electrical data.
The central wavelengths of the 4 CWDM channels are 1271, 1291, 1311 and 1331 nm as members of the CWDM wavelength grid defined in ITU-T G.694.2. It contains a duplex LC connector for the optical interface and a 38-pin connector for the electrical interface. To minimize the optical dispersion in the long-haul system, single-mode fiber (SMF) has to be applied in this module.
The product is designed with form factor, optical/electrical connection and digital diagnostic interface according to the QSFP+ Multi-Source Agreement (MSA). It has been designed to meet the harshest external operating conditions including temperature, humidity and EMI interference.
Absolute Maximum Ratings
It has to be noted that the operation in excess of any individual absolute maximum ratings might cause permanent damage to this module.
Parameter | Symbol | Min | Max | Unit | Notes |
Storage Temperature | TS | -40 | 85 | ℃ |
|
Operating Case Temperature | TOP | 0 | 70 | ℃ |
|
Power Supply Voltage | VCC | -0.5 | 3.6 | V |
|
Relative Humidity (non-condensation) | RH | 0 | 85 | % |
|
Damage Threshold, each Lane | THd | 3.3 |
| dBm |
|
Recommended Operating Conditions and Power Supply Requirements
Parameter | Symbol | Min | Typical | Max | Unit | Notes |
Operating Case Temperature | TOP | 0 |
| 70 | ℃ |
|
Power Supply Voltage | VCC | 3.135 | 3.3 | 3.465 | V |
|
Data Rate, each Lane |
|
| 10.3125 |
| Gb/s |
|
Control Input Voltage High |
| 2 |
| VCC | V |
|
Control Input Voltage Low |
| 0 |
| 0.8 | V |
|
Link Distance with G.652 | D | 0.002 |
| 10 | km |
|
Electrical Characteristics
The following electrical characteristics are defined over the Recommended Operating Environment unless otherwise specified.
Parameter | Test Point | Min | Typical | Max | Unit | Notes |
Power Consumption |
|
|
| 2.5 | W |
|
Supply Current | ICC |
|
| 0.7 | A |
|
Transceiver Power-on Initialization Time |
|
|
| 2000 | ms | 1 |
Transmitter (each Lane) | ||||||
Single-ended Input Voltage Tolerance (Note 2) |
| -0.3 |
| 4.0 | V | Referred to TP1 signal common |
AC Common Mode Input Voltage Tolerance |
| 15 |
|
| mV | RMS |
Differential Input Voltage Swing Threshold |
| 50 |
|
| mVpp | LOSA Threshold |
Differential Input Voltage Swing | Vin,pp | 190 |
| 700 | mVpp |
|
Differential Input Impedance | Zin | 90 | 100 | 110 | ohm |
|
Differential Input Return Loss |
| See IEEE 802.3ba 86A.4.11 | dB | 10MHz- 11.1GHz | ||
J2 Jitter Tolerance | Jt2 | 0.17 |
|
| UI |
|
J9 Jitter Tolerance | Jt9 | 0.29 |
|
| UI |
|
Data Dependent Pulse Width Shrinkage (DDPWS ) Tolerance |
| 0.07 |
|
| UI |
|
Eye Mask Coordinates {X1, X2, Y1, Y2} |
| 0.11, 0.31 95, 350 | UI mV | Hit Ratio = 5x10-5 | ||
Receiver (each Lane) | ||||||
Single-ended Output Voltage |
| -0.3 |
| 4.0 | V | Referred to signal common |
AC Common Mode Output Voltage |
|
|
| 7.5 | mV | RMS |
Differential Output Voltage Swing | Vout,pp | 300 |
| 850 | mVpp |
|
Differential Output Impedance | Zout | 90 | 100 | 110 | ohm |
|
Termination Mismatch at 1MHz |
|
|
| 5 | % |
|
Differential Output Return Loss |
| See IEEE 802.3ba 86A.4.2.1 | dB | 10MHz- 11.1GHz | ||
Common Mode Output Return Loss |
| See IEEE 802.3ba 86A.4.2.2 | dB | 10MHz- 11.1GHz | ||
Output Transition Time |
| 28 |
|
| Ps | 20% to 80% |
J2 Jitter Output | Jo2 |
|
| 0.42 | UI |
|
J9 Jitter Output | Jo9 |
|
| 0.65 | UI |
|
Eye Mask Coordinates {X1, X2, Y1, Y2} |
| 0.29, 0.5, 150, 425 | UI mV | Hit Ratio = 5x10-5 |
Notes:
Optical Characteristics
Parameter | Symbol | Min | Typical | Max | Unit | Notes | |
Wavelength Assignment | L0 | 1264.5 | 1271 | 1277.5 | nm |
| |
L1 | 1284.5 | 1291 | 1297.5 | nm |
| ||
L2 | 1304.5 | 1311 | 1317.5 | nm |
| ||
L3 | 1324.5 | 1331 | 1337.5 | nm |
| ||
Transmitter | |||||||
Side Mode Suppression Ratio | SMSR | 30 |
|
| dB |
| |
Total Average Launch Power | PT |
|
| 8.3 | dBm |
| |
Average Launch Power, each Lane | PAVG | -4 |
| 2.3 | dBm |
| |
Optical Modulation Amplitude (OMA), each Lane | POMA | -4 |
| 3.5 | dBm | 1 | |
Difference in Launch Power between any Two Lanes (OMA) | Ptx,diff |
|
| 6.5 | dB |
| |
Launch Power in OMA minus Transmitter and Dispersion Penalty (TDP), each Lane |
| -4.8 |
|
| dBm |
| |
TDP, each Lane | TDP |
|
| 2.6 | dB |
| |
Extinction Ratio | ER | 3.5 |
|
| dB |
| |
Relative Intensity Noise | RIN |
|
| -128 | dB/Hz | 12dB reflection | |
Optical Return Loss Tolerance | TOL |
|
| 20 | dB |
| |
Transmitter Reflectance | RT |
|
| -12 | dB |
| |
Transmitter Eye Mask Definition {X1, X2, X3, Y1, Y2, Y3} |
| {0.25, 0.4, 0.45, 0.25, 0.28, 0.4} |
|
| |||
Average Launch Power OFF Transmitter, each Lane | Poff |
|
| -30 | dBm |
| |
Receiver | |||||||
Damage Threshold, each Lane | THd | 3.3 |
|
| dBm | 2 | |
Total Average Receive Power |
|
|
| 8.3 | dBm |
| |
Average Receive Power, each Lane |
| -13.7 |
| 2.3 | dBm |
| |
Receiver Reflectance | RR |
|
| -26 | dB |
| |
Receiver Sensitivity (OMA), each Lane | SEN |
|
| -11.5 | dBm |
| |
Stressed Receiver Sensitivity (OMA), each Lane |
|
|
| -9.6 | dBm | 3 | |
Difference in Receive Power between any Two Lanes (OMA) | Prx,diff |
|
| 7.5 | dB |
| |
LOS Assert | LOSA | -28 |
|
| dBm |
| |
LOS Deassert | LOSD |
|
| -15 | dBm |
| |
LOS Hysteresis | LOSH | 0.5 |
|
| dB |
| |
Receiver Electrical 3 dB upper Cutoff Frequency, each Lane | FC |
|
| 12.3 | GHz |
| |
Conditions of Stress Receiver Sensitivity Test (Note 5) | |||||||
Vertical Eye Closure Penalty, each Lane |
|
| 1.9 |
| dB |
| |
Stressed Eye J2 Jitter, each Lane |
|
| 0.3 |
| UI |
| |
Stressed Eye J9 Jitter, each Lane |
|
| 0.47 |
| UI |
| |
Notes: